110 features ? 4 regulators combined in one package ? insulated single inline package ? sla 3005m/3006m have four 5v/0.5a outputs. sla3007m has three 5v/0.5a outputs and ch4 is a 3.3v/0.5a otuput for usb-ic ? low dropout voltage: v dif 0.5v (at i o =0.5a) ? output-independent on/off control terminal compatible with ls-ttl (active high) ? output-independent overcurrent and thermal protection circuits built in ? open collector flag-output terminals built in to output ocp operation to each output terminal (active low) excluding sla3007mch4 ? sla3005m/3007m (excluding ch4) for v o shutdown after ocp operation and sla3006m for continuous ocp operation ? built-in anti-malfunction delay circuit whose time can be set with an external capacitor applications ? usb hub power supplies ? electronic equipment absolute maximum ratings symbol v in v c i o p d1 p d2 t j t op t stg r t(j-c) r th(j-a) 4-output, low dropout voltage dropper type for usb hub sla3005m/3006m/3007m sla3005m/3006m/3007m unit v a c c symbol v in i o t jop t aop (t a =25 c) recommended operating conditions parameter dc input voltage voltage of output control terminal dc output current power dissipation junction temperature ambient operating temperature storage temperature thermal resistance (junction-to-case) thermal resistance (junction-to-ambient air) parameter dc input voltage range output current range operating junction temperature range ambient operating temperature range ratings 5.5 to 10 0 to 0.5 C20 to +100 C20 to +85 ratings sla3005m/3006m sla3007m 20 18 v in 0.5 30(with infinite heatsink) 3.36(without heatsink, stand-alone operation) C30 to +125 C30 to +100 C30 to +125 9.0 29.8(without heatsink, stand-alone operation) unit v v a w w c c c c/w c/w
111 parameter output voltage dropout voltage line regulation load regulation temperature coefficient of output voltage quiescent circuit current* 3 quiescent circuit current (output off)* 3 overcurrent protection starting current* 1 control voltage (output on) control voltage (output off) v c control current terminal *2 (output on) control current (output off) ocp detection voltage level delay threshold voltage delay terminal output current flag before ocp output detection terminal after ocp detection sla3005m/3006m/3007m *1 i s1 is specified at C5(%) drop point of output voltage v o on the condition that v in = 7v, i o = 0.1a. *2 output is on even when output control terminal v c is open. each input level is equivalent to ls-ttl. therefore, it may be directly driven by an ls-ttl circuit. *3 total of four circuits * the flg output latched by delay dly after ocp detection. (sla3005m/sla3007m (ch1 to 3) shuts down the output voltage simultan eously at latching.) set the v in or v c to low to reset latching. leave a time lag of c d 600s or more before restart. ** sla3007mch4 does not have the flg output function. unit v v mv mv mv/ c ma ma a v a a v v a v v electrical characteristics sla3005m min. typ. max. 4.85 5.00 5.15 v in =7v, i o =0.1a 0.5 i o 0.5a 30 v in =6 to 15v, i o =0.1a 50 v in =7v, i o =0 to 0.5a 0.5 v in =7v, i o =5ma, t j =C10 to 100 c 20 v in =7v, i o =0a 0.5 v in =7v, v c 1 to 4=0v 0.55 0.65 v in =7v 2.0 0.7 50 v c =2.7v C100 v c =0v 3.7 4.0 4.3 2.1 2.3 2.5 35 50 65 v in C0.4 r flg connected between flg and v in 0.5 i flg =1ma sla3006m min. typ. max. 4.85 5.00 5.15 v in =7v, i o =0.1a 0.5 i o 0.5a 30 v in =6 to 15v, i o =0.1a 50 v in =7v, i o =0 to 0.5a 0.5 v in =7v, i o =5ma, t j =C10 to 100 c 20 v in =7v, i o =0a 0.5 v in =7v, v c 1 to 4=0v 0.75 0.96 v in =7v 2.0 0.7 50 v c =2.7v C100 v c =0v 3.7 4.0 4.3 2.1 2.3 2.5 35 50 65 v in C0.4 r flg connected between flg and v in 0.5 i flg =1ma (t a =25 c unless otherwise specified) ratings symbol v o conditions v dif conditions ? v oline conditions ? v oload conditions ? v o / ? t a conditions i q conditions i q(off) conditions i s1 conditions v c. ih v c. il i c. ih conditions i c. il conditions v oth v dlyth i dly v flgh conditions v flgl conditions ch1, 2, 3 min. typ. max. 4.85 5.00 5.15 v in =7v, i o =0.1a 0.5 i o 0.5a 30 v in =6 to 15v, i o =0.1a 50 v in =7v, i o =0 to 0.5a 0.5 v in =7v, i o =5ma, t j =C10 to 100 c 20 v in =7v, i o =0a 0.5 v in =7v, v c 1 to 4=0v 0.55 0.65 v in =7v 2.0 0.7 50 v c =2.7v C100 v c =0v 3.7 4.0 4.3 2.1 2.3 2.5 35 50 65 v in C0.4 r flg connected between flg and v in 0.5 i flg =1ma sla3007m ch4 min. typ. max. 3.234 3.300 3.366 v in =7v, i o =0.1a 2.0 i o 0.5a 30 v in =6 to 15v, i o =0.1a 30 v in =7v, i o =0 to 0.2a 0.3 v in =7v, i o =5ma, t j =C10 to 100 c C C 0.55 0.65 v in =7v 2.0 0.7 50 v c =2.7v C100 v c =0v C C C C C
112 external dimensions block diagram a. part number b. lot number pin arrangement q v c1 w flg1 e dly1 r v o 1 t v c 2 y flg2 u dly2 i v o 2 o v c 3 !0 flg3 !1 dly3 !2 v o 3 !3 gnd !4 v c 4 !5 flg4 (sla3007m: nc) !6 dly4 (sla3007m: nc) !7 v o 4 !8 v in sla3005m sla3006m sla3007m 31 0.2 31.3 0.2 3.2 0.15 3.8 3.2 0.15 24.4 0.2 16.4 0.2 1.7 0.1 2.45 0.2 4 0.7 4.8 0.2 16 0.2 13 0.2 9.9 0.2 6.7 0.5 9.7 (3) r-end 0.55 +0.2 C0.1 +1 C0.5 1 +0.2 C0.1 0.65 +0.2 C0.1 17 p1.68 0.7 =28.56 1 13579 11 13 15 17 18 16 14 12 10 8 6 4 2 sk japan a b * * * sla3005m/3006m/3007m (unit:mm) plastic mold package type flammability: ul94v-0 weight: approx. 6g v o1 (4 pin) reset set v in (18 pin) v c1 (1 pin) flg 1 (2 pin) dly 1 (3 pin) + C + C C + ocp tsd latch v o2 (8 pin) reset set v c2 (5 pin) flg 2 (6 pin) dly 2 (7 pin) + C + C C + ocp tsd latch v o3 (12 pin) reset set v c3 (9 pin) flg 3 (10 pin) dly 3 (11 pin) + C + C C + ocp tsd latch v o4 (17 pin) reset set v c4 (14 pin) flg 4 (15 pin) gnd (13 pin) dly 4 (16 pin) + C + C C + ocp tsd latch v o1 (4 pin) reset set v in (18 pin) v c1 (1 pin) flg 1 (2 pin) dly 1 (3 pin) + C + C C + ocp tsd latch v o2 (8 pin) reset set v c2 (5 pin) flg 2 (6 pin) dly 2 (7 pin) + C + C C + ocp tsd latch v o3 (12 pin) reset set v c3 (9 pin) flg 3 (10 pin) dly 3 (11 pin) + C + C C + ocp tsd latch v o4 (17 pin) reset set v c4 (14 pin) flg 4 (15 pin) gnd (13 pin) dly 4 (16 pin) + C + C C + ocp tsd latch reset set + C + C C + ocp tsd latch reset set + C + C C + ocp tsd latch reset set + C + C C + ocp tsd latch v o1 (4 pin) reg4 v in (18 pin) v c1 (1 pin) flg 1 (2 pin) dly 1 (3 pin) v o2 (8 pin) v c2 (5 pin) flg 2 (6 pin) dly 2 (7 pin) v o3 (12 pin) v c3 (9 pin) flg 3 (10 pin) dly 3 (11 pin) v o4 (17 pin) v c4 (14 pin) n.c. (15 pin) gnd (13 pin) n.c. (16 pin) + C ocp tsd
113 t a -p d characteristics standard external circuit *1 c in : input capacitor (approx. 47 f) this capacitor is required if the input line is inductive and in the case of long wiring. *2 c o : output capacitor (47 to 220 f) *3 c d : delay time setting capacitor (0.1 f or more) use c d to set the delay time (t dly ) from when a low v o level due to ocp operation is detected until a flag signal is output. this prevents a rush current from causing malfunction at start. approximate calculation: t dly (c d v dlyth )/i dly [sec] when using soft start on v in or if c in has a large capacitance, set t dly long enough for the output voltage to rise sufficiently be sure to connect cd and do not use it for other applications, such as short circuiting cd. *4 d 1 to d 4 : reverse biasing protection diode this diode is required for protection against reverse biasing of the input and output. *5 r flg : set this to limit the inflow current into the flg terminal to 1ma or less. v in v in v o1 c in * 1 r flg * 5 + v c1 flg 1 v c1 flg 1 v o1 reg. 1 dly 1 * 3 c d1 * 2 c o1 * 4 d 1 + + + + v o2 r flg * 5 v c2 flg 2 v c2 flg 2 v o2 reg. 2 dly 2 * 3 c d2 * 2 c o2 * 4 d 2 + v o3 v c3 flg 3 v c3 flg 3 v o3 reg. 3 dly 3 * 3 * 2 c o3 * 4 d 3 + v o4 * 5 r flg * 5 r flg v c4 flg 4 v c4 flg 4 gnd v o4 reg. 4 dly 4 * 3 c d4 * 2 c o4 * 4 d 4 + + c d3 40 35 30 25 20 15 10 5 0 4-circuit total power dissipation p d (w) ambient temperature t a ( c) 0 C30 25 50 75 100 100 100 2mm (5.2 c/w) 75 75 2mm (7.6 c/w) (t c =25 c) infinite heatsink without heatsink heatsink: aluminum with silicon grease: g746 (shinetsu chemical industries) calculating the internal dissipation p d is calculated as follows: p d =[i o1 ?(v in -v o1 )]+[i o2 ?(v in -v o2 )]+[i o3 ?(v in -v o3 )]+[i o4 ?(v in -v o4 )]+v in ?ig estimating tj by temperature measurement 1. measuring position: at the root of pin 13 2. add the thermal resistance " j-l" between the junction and pin 13 and the pd product of each channel to the measured temperature. j-l is as follows : j-l1:8 c/w, j-l2:7 c/w, j-l3:5 c/w, j-l4:8 c/w the calculation formula is as follows :tj= j-l1?pd1+ j-l2?pd2+ j-l3?pd3+ j-l4?pd4+t13pin sla3005m/3006m/3007m sla3005m/3006m sla3007m timing chart sla3006m is1 voth t restart t dly i o v o v dly v flg v c sla3005m/sla3007m (excluding ch4) is1 voth v dlyth t restart t dly i o v o v dly v flg v c v dlyth v in v in v o1 c in * 1 r flg * 5 + v c1 flg 1 v c1 flg 1 v o1 ch1 dly 1 * 3 c d1 * 2 c o1 * 4 d 1 + + + + v o2 r flg * 5 v c2 flg 2 v c2 flg 2 v o2 ch2 dly 2 * 3 c d2 * 2 c o2 * 4 d 2 + v o3 v c3 flg 3 v c3 flg 3 v o3 ch3 dly 3 * 3 c d3 * 2 c o3 * 4 d 3 + v o4 * 5 r flg v c4 v c4 gnd v o4 ch4 * 2 c o4 * 4 d 4 +
114 typical characteristics sla3005m i o vs. v dif characteristics output voltage quiescent circuit current circuit current 1-circuit circuit current 4-circuits overcurrent protection characteristics v in vs. i s 1 characteristics line regulation load regulation on/off control characteristics v c terminal characteristics thermal protection characteristics 0.5 0.4 0.3 0.2 0.1 0 0 0.1 0.2 0.3 0.4 0.5 output current i o (a) dropout voltage v dif (v) 500 400 300 200 100 0 0 5 10 15 20 input voltage v in (v) quiescent circuit current 2 i q (off) ( a) v c 1, 2, 3, 4=0v 60 40 20 0 024681012 input voltage v in (v) ground current i g (ma) v c 1=open, v c 2, 3, 4=0v i o =0.5 to 0a 0.1a step 250 200 150 100 50 0 024681012 input voltage v in (v) ground current i g (ma) v c 1, 2, 3, 4=open i o =0.5a/ch i o =0.25a/ch i o =0a/ch 6 5 4 3 2 1 0 0 0.2 0.4 0.6 0.8 output current i o (a) output voltage v o (v) v in =5.5v 7v 10v c d =0v shut-down 12v 15v 0.80 0.75 0.70 0.65 0.60 0.55 0.50 56 8 101214161820 input voltage v in (v) overcurrent protection starting current i s 1 (a) 5.00 4.98 4.96 4.94 4.92 4.90 4 6 8 10 12 14 16 18 20 input voltage v in (v) output voltage v o (v) i o =0 to 0.5a 0.1a step 6 5 4 3 2 1 0 0 20 60 100 140 180 case temperature ( c) output voltage v o (v) v in =7v 6 5 4 3 2 1 0 0 0.5 1.0 1.5 2.0 2.5 3.0 output on/off control voltage v c (v) output voltage v o (v) 5.00 4.98 4.96 4.94 4.92 4.90 0 0.1 0.2 0.3 0.4 0.5 output current i o (a) output voltage v o (v) v in =5.5v 7v 10v 12v 15v 20v (t a =25 c) sla3005m/3006m/3007m 6 5 4 3 2 1 0 0123456 input voltage v in (v) output voltage v o (v) i o =0 to 0.5a 0.1a step 5 0 C5 C10 C15 C20 01234 output on/off control voltage v c (v) on/off control voltage i c ( a) v in =5.5v 7v 10v 20v
115 sla3005m/3006m/3007m typical characteristics sla3007m (t a =25 c) i o vs. v dif characteristics output voltage output voltage quiescent circuit current circuit current 1-circuit (ch1 to 3) circuit current (ch4) overcurrent protection characteristics overcurrent protection characteristics v in vs. i s 1 characteristics line regulation load regulation line regulation 0.5 0.4 0.3 0.2 0.1 0 0 0.1 0.2 0.3 0.4 0.5 output current i o (a) dropout voltage v dif (v) ch1 to 3 only 6 5 4 3 2 1 0 0123456 input voltage v in (v) output voltage v o (v) i o =0 to 0.5a 0.1a step ch1 to 3 only 4 3 2 1 0 0123456 input voltage v in (v) output voltage v o (v) i o =0 to 0.5a 0.1a step ch4 only 500 400 300 200 100 0 0 5 10 15 20 input voltage v in (v) quiescent circuit current i q (off) ( a) v c 1, 2, 3, 4=0v ch1 to 4 total 60 40 20 0 024681012 input voltage v in (v) ground current i g (ma) ch1 to 3 only i o =0.5 to 0a 0.1a step v c 1=open, v c 2, 3, 4=0v 40 30 20 10 0 024681012 input voltage v in (v) ground current i g (ma) ch4 only v c 1, 2, 3=0v i o =0.5 to 0a 0.1a step 6 5 4 3 2 1 0 0 0.2 0.4 0.6 0.8 output current i o (a) output voltage v o (v) c d =0v shut-down 12v 15v v in =5.5v 7v 10v ch1 to 3 only 4 3 2 1 0 0 0.2 0.4 0.7 0.6 output current i o (a) output voltage v o (v) v in =6v, 7v, 8v, 9v 10v ch4 only 0.80 0.75 0.70 0.65 0.60 0.55 0.50 56 8 101214161820 input voltage v in (v) overcurrent protection starting current i s 1 (a) same for ch1 to 4 5.00 4.98 4.96 4.94 4.92 4.90 4 6 8 101214161820 input voltage v in (v) output voltage v o (v) i o =0 to 0.5a 0.1a step ch1 to 3 only 5.00 4.98 4.96 4.94 4.92 4.90 0 0.1 0.2 0.3 0.4 0.5 output current i o (a) output voltage v o (v) v in =5.5v 7v 10v 12v 15v 18v ch1 to 3 only 3.32 3.30 3.28 3.26 3.24 3.22 3.20 4 6 8 10 12 14 16 18 input voltage v in (v) output voltage v o (v) i o =0 to 0.5a 0.1a step ch4 only
116 typical characteristics sla3007m (t a =25 c) load regulation on/off control characteristics v c terminal characteristics thermal protection characteristics sla3005m/3006m/3007m 3.32 3.30 3.28 3.26 3.24 3.22 3.20 0 0.1 0.2 0.3 0.4 0.5 output current i o (a) output voltage v o (v) v in =5.5v 6v 7v 10v ch4 only 6 5 4 3 2 1 0 0 0.5 1.0 1.5 2.0 2.5 3.0 output on/off control voltage v c (v) output voltage v o (v) ch1 to 3 ch4 5 0 C5 C10 C15 C20 01234 output on/off control voltage v c (v) on/off control voltage i c ( a) same for ch1 to 4 v in =5.5v 7v 10v 18v 6 5 4 3 2 1 0 0 20 60 100 140 180 case temperature ( c) output voltage v o (v) v in =7v ch1 to 3 ch4
|
